S29 - Chain Operated Fire Shutter 4 Hour Fire Rated

Our Series 29 4 Hour Fire Rated Manual Chain Operated roller shutters are a robust product ideally suited to protect commercial and industrial premises with opening up to 7000mm x 7000mm high, in addition to providing ease of operation when power and cost are a restraint.

The door is designed for opening applications where the need for protection is only in the event of fire. The roller shutter stays in the open position, if fire occurs, once the temperature has reached a threat level, the fusible link separates and releases the brake on the gearbox which brings down the door under gravity.

In addition, a manual solenoid can also be fitted allowing the door to be linked to the fire alarm which would also release the brake on the gearbox allowing the door to close under gravity.

Each roller shutter is made to measure and CE marked, ensuring each product complies with European directives and gives you peace of mind.

Each design has been thoroughly tested and inspected by Exova Warrington Fire Research to BS 476 Part 22 enabling us to issue Declaration Of Performance.

All our Roller Shutters are manufactured in house at our facility in Leigh and are subject to continuous product development, ensuring the products we offer are of the highest quality whilst maintaining ease of installation.

Each roller shutter can be manufactured to suit your specific requirements, with a dedicated team on hand to give advice and technical support, we can back up an already high quality product with first class service and support.

 

Options

  • Fusible Link
  • Manual Solenoid Release
  • Haul Chain Facility to open and close the door
  • Plastisol Curtain
  • Powder coated to any standard RAL or BS number
  • Special colours available at customer request
TECHNICAL SPECIFICATION

TESTED TO
B.S. 476 Part 22, Clause 8 (Uninsulated)
WARRES No. – 124382

SHUTTER TYPE
CONTROLLED DESCENT MANUAL

OPERATION
TO OPEN VIA HAUL CHAIN (THROUGH GEARBOX)
TO CLOSE BY RELEASING BRAKE ON GEARBOX (VIA PULL CORD)

MAXIMUM SIZE
5,000mm WIDE x 5,000mm HIGH

IMPORTANT NOTE!
FIRE SHUTTERS OPERATED ON A FREQUENT BASIS NEED TO BE ELECTRIC OPERATION

CURTAIN
Cold Rolled 3” curved traditional lath, galvanised to BS729:1971, 20 swg (0.9mm thick). Alternate laths are fitted with high quality pressed mild steel endlocks, which are double pop riveted to prevent lateral movement. A slotted full top lath is attached to the shutter barrel using high tensile hexagon head set screws, then the main curtain is attached. A high strength galvanised (BS729:1971) inverted “T- Section” bottom rail is added to the base of the curtain, typically 1.6mm thick, which incorporates a flat bar added for rigidity and fire intergrity. Weight bars are added to shutters below 6.5 square metres.

BARREL
5” Outside diameter Electric Resistance Welded tube (BS 6323), complete with uniquely fabricated helical wound torsion spring assembly, for counterbalancing of the shutter curtain, the counterbalance spring is “undersprung” to assist closure in the event of a fire. The assembly is mounted within the tube on a 25mm diameter steel shaft, complete with high quality mild steel bearing blocks, and high grade “sealed for life” bearings.

FLAGS
Endplates are constructed from flat 6mm thick mild steel plate (BS 1449) and bespoke mild steel “cups” are bolted to the endplate using high tensile hexagon head bolts, these “cups” are where the barrel shaft is supported. Fixing angles are formed using hot rolled angle section, 75mm x 50mm x 6mm which are slotted on the fixing face in accordance with the fire test requirements. Attached to the fixing angles are the galvanised (BS 729:1971) shutter guides, the guide section is typically 2 1/2” in depth x 1” inside dimension, the guide thickness is 3mm. A fusible link assembly is also fitted as standard (see note below). The flags are coated in a black primer paint finish.

HOOD
Slotted Fire Hood made from 20swg mild steel, galvanised to BS729:1971, c/w 50mm x 9mm obround shaped slots.

CONTROLLED DESCENT UNIT

Gravity descent unit. Optional Fusible Link (Heat Activation), Solenoid (Manual Reset – See options below) Platewheel & Sprocket Drive System, normally 1/2” x 5/16” pitch.

RELEASE MECHANISMS

(ONE OR BOTH MUST BE PROVIDED DEPENDING UPON APPLICATION)

FUSIBLE LINK

ACTIVATED VIA HEAT FROM LOCAL FIRE.ACTIVATION TEMPERATURE NORMALLY 68 DEGREES CENTIGRADE.

MANUAL RESET SOLENOID RELEASE

ACTIVATED UPON RECEIPT OF SIGNAL FROM FIRE ALARM / SMOKE DETECTOR.

IMPORTANT FIRE SIGNAL INFORMATION!

SIGNAL TYPE – 24 VOLT D.C. SIGNAL (MINIMUM 0.5 AMPS).
A BOOSTER PANEL CAN BE PROVIDED TO IF THE ALARM SYSTEM CANNOT PROVIDE CORRECT SIGNAL, THIS UNIT IS NOT INCLUDED AS STANDARD

WEIGHT
35 KGs Per Square Metre

Space Requirements

Face Fix

Maximum Width: 6000
Geared Sideroom: 150mm
Non-Geared Sideroom: 76mm Per Side

Between Fix

Maximum Width: 6000
Geared Sideroom: Lose 178mm
Non-Geared Sideroom: Lose 70mm

Maximum Height: 3000, 4550, 6000
Headroom: 375mm, 425mm, 525mm

Book A Quote Today

Contact Us


Unit D2(2)
Moss Industrial Estate St.
Helens Road
Leigh
WN7 3PT
01942 683601
 

altius  Altius Approved Vendor
dhf  Member Ref: 648
chas  Chas
construction-line  Constructionline

Select Page